The 10 Scariest Things About Saab 93 Key Fob

How to Replace a Saab 9-3 Key The Saab 9-3 is a car that has a large deal of appeal for drivers. It has good visibility and an efficient engine. It has a very high safety rating. It is essential to have two keys that are compatible for your vehicle. TheKeyLab can be expensive to replace a key in the event that you lose it. How to replace the ignition Key on a Saab 9-3 If your car key won't turn in the ignition you must replace it. This guide will show you how to replace the ignition key on the Saab 9-3. You will need a replacement key with a reprogrammable battery and a new key-fob case. Unlike older models, most modern Saab cars have a transponder on the key-fob rather than a physical metal key to unlock and start the car. The issue with this is that the reprogrammable battery in the key-fob will eventually wear out and lose charge for long. This is especially the case if you use the same key in the same lock. The good news is that it can be replaced fairly easily by an experienced locksmith. You can also do it yourself if you have the right tools and a bit of patience. The first step is separating the key-fob. This is done by inserting a flathead screwdriver into the slot located in the middle of the case. It is important to work slowly, since the plastic is very thin and can easily be damaged. After the case has been opened and the case is opened, you can make the new key by combining the lower half of the key that was used previously with the transponder and banana on the new key. This will ensure that the new key is connected to the CIM correctly, which could make a big difference when replacing the original key for your Saab 9-3. How to replace the ignition Key in a Saab 900 If you don't have two keys, you'll need to remove the steering wheel and dashboard in order to access the ignition. Begin by disconnecting the negative battery cable. After the battery has been removed, you can remove all trim pieces and dashboard pieces that surround the steering wheel. After the dashboard has been removed, you can put a screwdriver in the opening behind the ignition switch. The ignition barrel is equipped with a key lock which could prevent the vehicle from starting if it does not contain the key. If the ignition switch on your 900 isn't functioning properly, check to see whether the key is within the lock or inside the ignition barrel. You should also rotate your keys and keep them clean to avoid breaking. Saab cars differ from other cars in that they don't use traditional keys made of metal. Instead, the car is able to recognize the electronic signals generated by the key fob through a chip that is specifically designed for it. If you have lost your only working key fob the dealer will charge the highest dollar for replacing your computer module (known as the CIM). However, we can reprogram your existing computer's EEPROM and set it to accept new keys without replacing it. This will save you up to 50% of the price the dealer charges! We call it the SAAB KEY PROGRAM. Find out more here! How to replace the ignition Key in a Saab9-5 The metal part of a traditional Saab key is simple to copy, and is not a major obstacle against theft of vehicles. The electronic component of the key fob has a chip that can recognize the car when the key is inserted into the ignition switch. Saab has relied on the technology of this anti-theft system for more than a decade. It's not quite as effective as a physical lock for your door however, it makes the theft of your car much more difficult. This is the reason why every Saab owner should always have an extra key available. The majority of new Saabs come with two keys, however they are also available for purchase at the dealer's expense using a handheld device referred to as Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception is NG 9-3 cars, which are equipped with modernized, more modern features that require a different key-fob and work through a different process. If you lose all keys, the dealer will replace your CIM or TWICE modules and charge you the cost of replacement. But we can reprogram the EEPROM in your existing computer and make it accept new keys without replacing the expensive modules. How to Replace the Ignition Key on an XC90 Saab If your SAAB 9-3 key fob is having trouble turning the barrel of the lock it's possible that it's time to replace it. The procedure is quite simple and doesn't require you to visit a dealer. Instead, you can do it yourself at home with some basic tools. First, you'll need to prepare the keys for your new car. Before you begin, ensure that the anti-theft system is disabled by placing blocks on your rear wheels and engaging the handbrake. Then, insert the key into the ignition and turn it to the ON position which activates the accessories but it doesn't start the engine. Repeat this 5 times, and then keep the key on the “on” position. Then you'll need to buy an additional case for your key fob. They are readily available at many auto parts stores and are typically inexpensive. You can purchase them without electronics, based on the model. To open the case, insert a flathead screwdriver in the slot that is in the middle and gently work it. The case will split easily and, once you do, you'll have access to the internal electronics. Use a flathead screwdriver to gently remove the electronics.